Made with a rugged, weatherproof construction, Bedrugs make a great aftermarket accessory for you truck - Oil, grease, spills, and stains, can easily be washed out with soap and water from a garden hose or high pressure washer.
Ideal for sporting or boating equipment, hunting gear, golf clubs.
Molded foam bottom will not scratch your truck bed like hard liners do.
Easy to clean.
Easy Installation, fits like a glove.
BedRug floors, walls, tailgates and bulkheads are heat and pressure molded specifically to fit each truck model.
Precision die-cutting to rigid factory specifications assure that a BedRug fits like a glove!
All bed features such as: 2 tier loading, load locking slots, & tie down devices remain usable.
Comfort The plastic foam backing is molded to conform exactly to the floor ribs. This creates a flat cushioned floor that is very "knee friendly". When kneeling, sitting, or lying on floor, you almost do not feel the floor ribs. Wonderful for outdoor activities, sporting events and makes a great sleeping surface for camping.
Acid, Grease and Chemical Proof
The solid plastic polymer fiber can not be permanently marked by transmission fluid, oil, grease or gasoline.
Acids, solvents, chemical compounds, or petroleum products will not damage the carpet-like plastic fiber surface or foam bottom.
The closed-cell foam bottom will not soak up ANY liquid.
Waterproof and Stain Resistant Water is not absorbed by the closed-cell foam bottom. Any spill or stain remains on the stain-resistant plastic fiber surface for easy cleaning.
Easy To Clean!!
Drink spills and pet accidents will not penetrate either the foam or the plastic fiber surface, simply blot them up with paper towels or other absorbent material.
Dirt and spills can be cleaned with soap and water using a garden hose or high pressure washer with detergent soap.
Oil, grease, spills, and stains, can easily be washed out with soap and water from a garden hose or high pressure washer.
Dry dirt, dust, scraps, or shavings can easily be cleaned with a shop or household vacuum.
Odors cannot be absorbed and absolutely will not linger after all odor holding particles are flushed from the carpet.
Truck bed surface temperature should be at least 68°F for proper installation. Warning: Improper installation will result in liner flying out of truck!
Follow instructions exactly!!
Read all instructions before installing.
The floor and siderugs are shipped unzipped.
Remove floor and siderugs from box.
Zip floor and siderugs together to form the one-piece soft bed liner.
A very aggressive hook and loop fastening system has been designed to hold the bedliner in open bed trucks.
A continuous loop fastener is sewn around the liner. The bulkhead and tailgate have two continuous strips of loop fastener sewn along the top and bottom. The hook fasteners have a self-adhesive backing to stick to the bed of the truck.
Lay the Bedrug soft bed liner in the bed of the truck to determine the exact location and fit.
Note: Some truck beds are equipped with tie-down hooks, load extenders and other functional equipment. These may be located on the floor, bulkhead or sidewalls. For equipment such as this, the installer must either:
» Cut a small slit in the appropriate area of the Bedrug allowing the equipment to protrude through the Bedrug into the truck bed. (This will not damage the Bedrug.) or
» Remove the equipment until the installation is complete, then reinstall the equipment on top of the Bedrug.IMPORTANT: Never cut or put slits through any seams or sewn areas of the Bedrug. This will cause the seam to come completely apart.Refer to illustration for completing steps 8 -14. Roll one side of the Bedrug up exposing the floor area where the 3" strip of hook fastener is to be adhered.
Roll one side of the Bedrug up, exposing the floor area, where the 3" strip of hook fastener is to be adherred.
Using a clean lint-free cloth, clean this area thoroughly using NON-PETROLEUM based solvent. Then with a separate cloth, clean the same area again with alcohol. If the cloths become visually soiled, replace them with clean ones.
Attach hook fasteners to the loop. For siderugs, be sure to place the 2" long hook fasteners at the locator marks which are molded into the foam. Remove the protective liners for the hook fasteners exposing the adhesive. (See Illustration) Lay the Bedrug down, then FIRMLY rub the fastener(s) down VERY AGGRESSIVELY to assure full engagement of the fastener(s) and the adhesive. Note: Truck bed surface temperature should be 68°F or higher in order for the hook fastener to achieve maximum adhesion. Also, never contaminate the adhesive by touching it with your fingers.
Repeat steps 9 and 10 for the opposite side of the Bedrug.
Comfort The plastic foam backing is molded to conform exactly to the floor ribs. This creates a flat cushioned floor that is very "knee friendly". When kneeling, sitting, or lying on floor, you almost do not feel the floor ribs. Wonderful for outdoor activities, sporting events and makes a great sleeping surface for camping.
Acid, Grease and Chemical Proof
Waterproof and Stain Resistant Water is not absorbed by the closed-cell foam bottom. Any spill or stain remains on the stain-resistant plastic fiber surface for easy cleaning.
Easy To Clean!!
